Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread:
How to use the stock rol as a debug light for RGH hack

  1. #1
    Junior Member
    Join Date
    Mar 2012
    Posts
    10
    Thanked: 5
    Mentioned
    0 Post(s)

    How to use the stock rol as a debug light for RGH hack

    This tut will show you how to use the stock light on the rol as a debug light for the rgh hack.

    you will need one 1n4148 switching diode ( same as used on jtag hack ) and some wire.

    please look at picks for the proper install of the diode.

    Ok you need to download and program the custom ground debug light .jed to you console.
    Then put the diode on the debug pad or pin of your glitch chip.
    Run a wire from the diode up to the rol and solder it to the green negitive pad.

    please note the xbox 360 uses a common positive (not negitive) for its lights this is why
    you must use the custom negitive .jed because the normal .jed uses pos on the debug pad and the custom .jed
    has been switched to negitive.

    you can down load the fat model custom ground debug .jeds here (i have not tested the slim yet will update the link after its done)

    http://glumbouploads.com/dzaqm1msh6l0








    http://www.youtube.com/watch?feature...&v=MefL2ixnuQ8

    update--- the slim uses common negitive for its lights so dont do any of this to a slim

    new update-- you can use the normal .jed (not the custom one ) for your slim.
    just put the diode on the debug pad as seen the pics and run a wire up to the positive side of one of the stock lights and that it your done.
    Last edited by 2quick4u; 03-23-2012 at 11:54 PM.

  2. #2
    HacksDen Staff
    Administrator
    Krafter's Avatar
    Join Date
    Mar 2011
    Location
    Where you're not
    Posts
    2,909
    Thanked: 764
    Blog Entries
    1
    Mentioned
    5 Post(s)
    Sorry for the delay on this. Our spam filter caught this one.

    Thanks for posting this. I have wondered how to do this myself but have always been in to much of a hurry to figure it out but now I know.
    Judge me by the content of my character and not the color of my politics.
    Feedback from my work: 1, 2, 3, 4

  3. #3
    Founding Member WhiteShad0wX's Avatar
    Join Date
    Mar 2011
    Location
    I'm right here
    Posts
    287
    Thanked: 59
    Mentioned
    0 Post(s)
    I cannot see 2quick4u's post. I only see Krafter's.

  4. #4
    HacksDen Staff
    Administrator
    Krafter's Avatar
    Join Date
    Mar 2011
    Location
    Where you're not
    Posts
    2,909
    Thanked: 764
    Blog Entries
    1
    Mentioned
    5 Post(s)
    How about now?

    Sent from my DROID2 using Tapatalk
    Judge me by the content of my character and not the color of my politics.
    Feedback from my work: 1, 2, 3, 4

  5. #5
    Junior Member
    Xbox Junkie!
    knowlzy10's Avatar
    Join Date
    Feb 2012
    Location
    workington, cumbria, england
    Posts
    585
    Thanked: 298
    Blog Entries
    1
    Mentioned
    0 Post(s)
    Same here m8 not seeing no tutorial, was meant to mention that this morning when i first so the post

    Sent from my GT-I9100 using Tapatalk





  6. #6
    HacksDen Staff
    Moderator
    RobGee789's Avatar
    Join Date
    Mar 2011
    Posts
    4,706
    Thanked: 1660
    Mentioned
    12 Post(s)
    i can see all
    Need any gfx making HERE is where to ask

  7. #7
    HacksDen Staff
    Administrator
    Krafter's Avatar
    Join Date
    Mar 2011
    Location
    Where you're not
    Posts
    2,909
    Thanked: 764
    Blog Entries
    1
    Mentioned
    5 Post(s)
    Should be able to see it now. It was still moderated lol.

    Sent from my DROID2 using Tapatalk
    Judge me by the content of my character and not the color of my politics.
    Feedback from my work: 1, 2, 3, 4

  8. #8
    Junior Member
    Xbox Junkie!
    knowlzy10's Avatar
    Join Date
    Feb 2012
    Location
    workington, cumbria, england
    Posts
    585
    Thanked: 298
    Blog Entries
    1
    Mentioned
    0 Post(s)
    Can see it now! Helps when you open your eyes lol

    Sent from my GT-I9100 using Tapatalk





  9. #9
    Enthusiast dgenx's Avatar
    Join Date
    Feb 2012
    Location
    south coast uk
    Posts
    441
    Thanked: 155
    Mentioned
    0 Post(s)
    this looks like fun to try..i await the slim version

  10. #10
    Junior Member
    Join Date
    Mar 2012
    Posts
    10
    Thanked: 5
    Mentioned
    0 Post(s)
    On the slim rol board you will see little white dots next to the lights.The side with the dot is ground so hook your wire to the other side of the
    light witch is pos +

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •